Sailvde Sensor Night Vision Mini Camera HD Camcorder 1080P Monitor Small Security Camera Surveillance Secret Video Recorder

1. Power button; 2. M button-mode button; 3. Lanyard hole; 4. Indicator light; 5. TF card slot;

6. USB; 7. Reset button; 8. Night vision light; 9. Lens

1. Product parameters:

Video format: AVI

Video encoding: M-JPEG

Video resolution: 1920*1080 1280*720

Video frame rate: 30fps

Camera resolution: 4032*3024

Picture format: JPG

Battery capacity: about 170mah

Recording time: about 60 minutes

Charging voltage: DC-5V 1A

Storage support: 8GB-32GB

Transmission speed: USB 2.0

Interface type: Mini 8PIN USB

2. Operation guide (please perform the following operations after inserting the card normally)

Note: 1. When the battery power is low, the red and blue lights flash for 5 seconds and then the machine will shut down directly.

2. There is no card when the machine is turned on, and the red and blue lights will flash for 5 seconds and then the machine will automatically shut down.

3. There is no working mode after booting, and it will automatically shut down after 1 minute.

1) Charging:

This machine has a built-in rechargeable lithium battery. When the power of the machine is low, please charge it. You can charge it in the following ways:

1. Connect a 5V charger;

2. Connect the mobile power supply;

3. Connect the computer USB port.

Note: The red light flashes when charging, and the red light is on when it is fully charged.

Press the power button for 2 seconds to turn on, the blue light will be on after turning on, and it is in standby mode.

2) 720P video recording:

In standby mode, click the power button once, and the blue light flashes 3 times to go out to enter the recording. During recording, there is no indicator light prompt; during recording, click the power button once to stop and save the recording, the blue light is on, and it returns to standby mode.

A video of 5 minutes, automatically saved in segments, and supports loop coverage.

3) 1080P video recording:

In standby mode, click the mode button once, the red and blue lights are on for 1080P recording mode, and then click the power button once, the red lights flash three times, and the red and blue lights are off at the same time to enter the recording; during recording, click the power button once to stop saving Recording, the red and blue lights are on at the same time, and it returns to standby mode.

A video of 5 minutes, automatically saved in segments, and supports loop coverage.

4) Take pictures:

In standby mode, click the mode button twice, the red light is on and the blue light is off. In this mode, click the power button once, the red light will flash once, and a picture will be generated and saved. To continue taking pictures, click the power button again.

5) The infrared light is turned on and off:

Turn on: In any mode after booting, press the power button for about 2 seconds to release, the red light flashes 2 times, and the infrared night vision light is turned on.

Turn off: In any mode, press the power button for about 2 seconds to release, the red light flashes 3 times, and the infrared night vision function is turned off.

6) Motion detection mode (720P -1080P):

720P motion detection: After booting, the blue light is always on, long press the mode button for 3 seconds and release it, the red light flashes 3 times, and the blue light is on, that is, the motion detection recording mode is turned on. After a moving object is detected , The blue light goes out to enter the motion detection recording; after 5 minutes, the recording is automatically saved. If there is no moving object, the blue light is on and the machine is in the detection state; when there is a moving object, the blue light is off, and the video is entered. (Press any button once to exit the motion detection mode).

1080P motion detection: After booting into standby mode, click the mode button once, the red and blue lights are on, the machine is in 1080P video mode, long press the mode button for 3 seconds, the red lights flash 3 times, red and blue lights at the same time to enter motion detection Recording mode, after detecting the movement of the object, the red and blue lights will be off at the same time to enter the motion detection recording. After 5 minutes, the video is automatically saved. If there is no moving object, the red and blue lights are on, and the machine is in the detection state; when there is a moving object, the red and blue lights are off, and the video is entered. (Press any button once to exit the motion detection mode).

7) Record while charging:

Connect the charger or mobile power supply to record while charging, or you can manually stop recording and switch to any mode.

8) Reset:

The machine crashes, the buttons are invalid, and cannot be used normally, you can click the button in the reset hole to reset the machine.

9) Shut down:

In any mode, press and hold the power button for about 6 seconds, and all the red and blue lights will go out to shut down. When no functions are used in standby mode, it will automatically shut down after 1 minute of standby.

10) Time modification:

After the machine is turned on, it will automatically create a TXT text file (TIMEREST.txt) in the root directory of the TF card. When it is turned off, use the data cable to connect to the computer. After opening the TIMEREST.txt file on the removable disk, edit the time and format (year) you need. Month, day, hour, minute and second) After 20180101192526 Y, save the file, and the machine can be burned into the machine normally after the boot time.

The machine does not display the time by default. If you need to display the time watermark, change the N in the file to Y. The reference format is as follows:

1: 20180101192526 Y (with time watermark display)

2: 20180101192526 N (no time watermark display)

Precautions:

Use occasion: Please strictly abide by the relevant laws of the country where it is used, and do not use this product for any illegal purpose, otherwise

Fruit conceited.

Working temperature: Please use it at natural temperature, do not use it at a temperature that the human body cannot adapt to.

Working Humidity: Please use it under the suitable environment humidity for human beings. Do not put the product in a humid working environment. This product is not equipped with

Water function, avoid being exposed to water or rain.

Shooting requirements: Please use it in an environment with sufficient light source. Do not point the camera directly at the sun and other strong light sources to avoid optics

Pieces are damaged.

Cleaning requirements: do not use in an environment with excessive dust density, so as to prevent the lens and other parts from being contaminated with dust and affecting the camera